View STK22C48_1189727.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STK22C48
2Kx8 AutoStore nvSRAM FEATURES
* 25, 45 ns Read Access & R/W Cycle Times * Unlimited Read/Write Endurance * Automatic Non-Volatile STORE on Power Loss * Non-Volatile STORE Under Hardware Control * Automatic RECALL to SRAM on Power Up * Unlimited RECALL Cycles * 1 Million STORE Cycles * 100-Year Non-volatile Data Retention * Single 5V + 10% Operation * Commercial, Industrial, and Military Temperatures * 28-Pin 300 mil SOIC or 330 mil SOIC (RoHSCompliant) DESCRIPTION The Simtek STK22C48 is a 16Kb fast static RAM with a nonvolatile Quantum Trap storage element included with each memory cell. The SRAM provides the fast access & cycle times, ease of use, and unlimited read & write endurance of a normal SRAM. Data transfers automatically to the non-volatile storage cells when power loss is detected (the STORE operation). On power-up, data is automatically restored to the SRAM (the RECALL operation). Both STORE and RECALL operations are also available under software control. The Simtek nvSRAM is the first monolithic non-volatile memory to offer unlimited writes and reads. It is the highest-performance, most reliable non-volatile memory available.
BLOCK DIAGRAM
VCCX VCAP
Quantum Trap 32 x 512
POWER CONTROL
A5 A6 A7 A8 A9
ROW DECODER
STORE STATIC RAM ARRAY 32 x 512 RECALL
STORE/ RECALL CONTROL
HSB
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7
INPUT BUFFERS
COLUMN I/O COLUMN DEC
A0 A1 A2 A3 A4 A10
G E W
This product conforms to specifications per the terms of Simtek standard warranty. The product has completed Simtek internal qualification testing and has reached production status.
1
Document Control #ML0004 Rev 0.3 February 2007
STK22C48
PIN CONFIGURATIONS
VCAP NC A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15
VCCX W HSB A8 A9 NC G A10 E DQ7 DQ6 DQ5 DQ4 DQ3
28-pin 300 mil SOIC 28-pin 330 mil SOIC
PIN NAMES
Pin Name A10-A0 DQ7-DQ0 E W G VCC VSS Input I/O Input Input Input Power Supply Power Supply I/O Description Address: The 11 address inputs select one of 2,048 bytes in the nvSRAM array Data: Bi-directional 8-bit data bus for accessing the nvSRAM Chip Enable: The active low E input selects the device Write Enable: The active low W enables data on the DQ pins to be written to the address location latched by the falling edge of E Output Enable: The active low G input enables the data output buffers during read cycles. De-asserting G high caused the DQ pins to tri-state. Power: 5.0V, 10% Ground
Document Control #ML0004 Rev 0.3 February 2007
2
STK22C48
ABSOLUTE MAXIMUM RATINGSa
Voltage on Input Relative to Ground . . . . . . . . . . . . . -0.5V to 7.0V Voltage on Input Relative to VSS . . . . . . . . . . -0.6V to (VCC + 0.5V) Voltage on DQ0-7 or HSB . . . . . . . . . . . . . . . . -0.5V to (VCC + 0.5V) Temperature under Bias . . . . . . . . . . . . . . . . . . . . .-55C to 125C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to 150C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1W DC Output Current (1 output at a time, 1s duration) . . . . . . . 15mA
Note a: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
DC CHARACTERISTICS
COMMERCIAL SYMBOL ICC1b ICC2c ICC3
b
(VCC = 5.0V 10%)e
INDUSTRIAL UNITS MIN MAX 85 65 3 10 2 25 18 1.5 1 5 2.2 VSS - .5 2.4 0.4 0.4 0 70 -40 VCC + .5 0.8 2.2 VSS - .5 2.4 0.4 0.4 85 MIN 90 65 3 10 2 26 19 1.5 1 5 VCC + .5 0.8 MAX mA mA mA mA mA mA mA mA A A V V V V V C tAVAV = 25ns tAVAV = 45ns All Inputs Don't Care, VCC = max W (V CC - 0.2V) All Others Cycling, CMOS Levels All Inputs Don't Care tAVAV = 25ns, E VIH tAVAV = 45ns, E VIH E (V CC - 0.2V) All Others VIN 0.2V or (VCC - 0.2V) VCC = max VIN = VSS to VCC VCC = max VIN = VSS to VCC, E or G VIH All Inputs All Inputs IOUT = - 4mA except HSB IOUT = 8mA except HSB IOUT = 3mA NOTES
PARAMETER Average VCC Current Average VCC Current during STORE Average VCC Current at tAVAV = 200ns 5V, 25C, Typical Average VCAP Current during AutoStore Cycle Average VCC Current (Standby, Cycling TTL Input Levels) VCC Standby Current (Standby, Stable CMOS Input Levels) Input Leakage Current Off-State Output Leakage Current Input Logic "1" Voltage Input Logic "0" Voltage Output Logic "1" Voltage Output Logic "0" Voltage Logic "0" Voltage on HSB Output Operating Temperature
ICC4c ISB1d ISB2d IILK IOLK VIH VIL VOH VOL VBL TA
Note b: Note c: Note d: Note e:
ICC1 and ICC3 are dependent on output loading and cycle rate. The specified values are obtained with outputs unloaded. ICC2 and ICC4 are the average currents required for the duration of the respective STORE cycles (tSTORE ) . E VIH will not produce standby current levels until any nonvolatile cycle in progress has timed out. VCC reference levels throughout this datasheet refer to VCCX if that is where the power supply connection is made, or VCAP if VCCX is connected to ground. 5.0V
AC TEST CONDITIONS
Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 3V Input Rise and Fall Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5ns Input and Output Timing Reference Levels . . . . . . . . . . . . . . . .1.5V Output Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Figure 1
480 Ohms OUTPUT 255 Ohms 30 pF INCLUDING SCOPE AND FIXTURE
CAPACITANCEf
SYMBOL CIN COUT PARAMETER Input Capacitance Output Capacitance
(TA = 25C, f = 1.0MHz)
MAX 8 7 UNITS pF pF CONDITIONS V = 0 to 3V V = 0 to 3V
Note f:
These parameters are guaranteed but not tested.
Figure 1: AC Output Loading
Document Control #ML0004 Rev 0.3 February 2007
3
STK22C48
SRAM READ CYCLES #1 & #2
SYMBOLS NO. #1, #2 1 2 3 4 5 6 7 8 9 10 11 tELQV tAVAVg tAVQVh tGLQV tAXQXh tELQX tEHQZi tGLQX tGHQZ
i
(VCC = 5.0V 10%)e
STK22C48-25 PARAMETER STK22C48-45 UNITS MIN MAX 25 25 25 10 5 5 10 0 10 0 25 0 45 0 15 5 5 15 45 45 20 MIN MAX 45 ns ns ns ns ns ns ns ns ns ns ns
Alt. tACS tRC tAA tOE tOH tLZ tHZ tOLZ tOHZ tPA tPS Chip Enable Access Time Read Cycle Time Address Access Time Output Enable to Data Valid Output Hold after Address Change Chip Enable to Output Active Chip Disable to Output Inactive Output Enable to Output Active Output Disable to Output Inactive Chip Enable to Power Active Chip Disable to Power Standby
tELICCHf tEHICCL
f
Note g: W and HSB must be high during SRAM READ cycles. Note h: Device is continuously selected with E and G both low. Note i: Measured 200mV from steady state output voltage.
SRAM READ CYCLE #1: Address Controlledg, h
2 tAVAV ADDRESS 5 tAXQX DQ (DATA OUT)
DATA VALID
3 tAVQV
SRAM READ CYCLE #2: E Controlledg
tAVAV ADDRESS tELQV E
6 tELQX 7 1 2
tEHICCL
11
tEHQZ
G tGLQV
4
tGHQZ
9
tGLQX DQ (DATA OUT)
10 tELICCH DATA VALID
8
ACTIVE
ICC
STANDBY
SRAM WRITE CYCLES #1 & #2
SYMBOLS NO. #1 12 13 tAVAV tWLWH #2 tAVAV tWLEH Alt. tWC tWP Write Cycle Time Write Pulse Width PARAMETER
(VCC = 5.0V 10%)e
STK22C48-25 MIN 25 20 MAX STK22C48-45 UNITS MIN 45 30 MAX ns ns
Document Control #ML0004 Rev 0.3 February 2007
4
STK22C48
SYMBOLS NO. #1 14 15 16 17 18 19 20 21 tELWH tDVWH tWHDX tAVWH tAVWL tWHAX tWLQZ i, j tWHQX #2 tELEH tDVEH tEHDX tAVEH tAVEL tEHAX Alt. tCW tDW tDH tAW tAS tWR tWZ tOW Chip Enable to End of Write Data Set-up to End of Write Data Hold after End of Write Address Set-up to End of Write Address Set-up to Start of Write Address Hold after End of Write Write Enable to Output Disable Output Active after End of Write 5 PARAMETER MIN 20 10 0 20 0 0 10 5 MAX MIN 30 15 0 30 0 0 15 MAX ns ns ns ns ns ns ns ns STK22C48-25 STK22C48-45 UNITS
Note j: If W is low when E goes low, the outputs remain in the high-impedance state. Note k: E or W must be VIH during address transitions. Note l: HSB must be high during SRAM WRITE cycles.
SRAM WRITE CYCLE #1: W Controlledk, l
12 tAVAV ADDRESS 14 tELWH E 17 tAVWH 13 tWLWH 15 tDVWH DATA IN 20 tWLQZ
PREVIOUS DATA DATA VALID
19 tWHAX
18 tAVWL W
16 tWHDX
DATA OUT
HIGH IMPEDANCE
21 tWHQX
SRAM WRITE CYCLE #2: E Controlledk, l
12 tAVAV ADDRESS 18 tAVEL E 14 tELEH 19 tEHAX
17 tAVEH W
13 tWLEH 15 tDVEH 16 tEHDX
DATA VALID HIGH IMPEDANCE
DATA IN DATA OUT
Document Control #ML0004 Rev 0.3 February 2007
5
STK22C48
HARDWARE MODE SELECTION
E H L L X X H L X W H H H L HSB X X X X A12 - A0 (hex) Not Selected Read SRAM Write SRAM Nonvolatile STORE MODE I/O Output High Z Output Data Input Data Output High Z POWER Standby Active Active lCC2 m n NOTES
Note m: HSB STORE operation occurs only if an SRAM write has been done since the last nonvolatile cycle. After the STORE (if any) completes, the part will go into standby mode, inhibiting all operations until HSB rises. Note n: I/O state assumes G < VIL. Activation of nonvolatile cycles does not depend on state of G.
HARDWARE STORE CYCLE
SYMBOLS NO. Standard 22 23 24 25 26 tSTORE tDELAY tRECOVER tHLHX tHLBL Alternate tHLHZ tHLQZ tHHQX STORE Cycle Duration Time Allowed to Complete SRAM Cycle Hardware STORE High to Inhibit Off Hardware STORE Pulse Width Hardware STORE Low to Store Busy PARAMETER
(VCC = 5.0V 10%)e
STK22C48 UNITS NOTES MIN MAX 10 1 700 15 300 ms s ns ns ns i, o i, p o, q
Note o: E and G low for output behavior. Note p: E and G low and W high for output behavior. Note q: tRECOVER is only applicable after tSTORE is complete.
HARDWARE STORE CYCLE
25 tHLHX HSB (IN) 24 tRECOVER 22 tSTORE
HSB (OUT)
HIGH IMPEDANCE
26 tHLBL
HIGH IMPEDANCE
23 tDELAY DQ (DATA OUT)
DATA VALID DATA VALID
Document Control #ML0004 Rev 0.3 February 2007
6
STK22C48
AutoStore / POWER-UP RECALL
SYMBOLS NO. Standard 27 28 29 30 31 32 tRESTORE tSTORE tVSBL tDELAY VSWITCH VRESET tBLQZ tHLHZ Alternate Power-up RECALL Duration STORE Cycle Duration Low Voltage Trigger (VSWITCH) to HSB Low Time Allowed to Complete SRAM Cycle Low Voltage Trigger Level Low Voltage Reset Level 1 4.0 4.5 3.6 PARAMETER MIN MAX 550 10 300 s ms ns s V V r p, s l o
(VCC = 5.0V 10%)e
STK22C48 UNITS NOTES
Note r: tRESTORE starts from the time VCC rises above VSWITCH. Note s: HSB is asserted low for 1s when VCAP drops through VSWITCH. If an SRAM write has not taken place since the last nonvolatile cycle, HSB will be released and no STORE will take place.
AutoStore / POWER-UP RECALL
VCC 31 VSWITCH 32 VRESET
AutoStoreTM
POWER-UP RECALL 27 tRESTORE HSB 30 tDELAY W 29 tVSBL 28 tSTORE
DQ (DATA OUT)
POWER-UP RECALL
BROWN OUT NO STORE (NO SRAM WRITES) NO RECALL (VCC DID NOT GO BELOW VRESET)
BROWN OUT AutoStore NO RECALL (VCC DID NOT GO BELOW VRESET)
BROWN OUT AutoStore RECALL WHEN VCC RETURNS ABOVE VSWITCH
Document Control #ML0004 Rev 0.3 February 2007
7
STK22C48 nvSRAM OPERATION
The STK22C48 has two separate modes of operation: SRAM mode and nonvolatile mode. In SRAM mode, the memory operates as a standard fast static RAM. In nonvolatile mode, data is transferred from SRAM to Nonvolatile Elements (the STORE operation) or from Nonvolatile Elements to SRAM (the RECALL operation). In this mode SRAM functions are disabled.
POWER-UP RECALL
During power up, or after any low-power condition (VCAP < VRESET), an internal RECALL request will be latched. When VCAP once again exceeds the sense voltage of VSWITCH, a RECALL cycle will automatically be initiated and will take tRESTORE to complete. If the STK22C48 is in a WRITE state at the end of power-up RECALL, the SRAM data will be corrupted. To help avoid this situation, a 10K Ohm resistor should be connected either between W and system VCC or between E and system VCC.
NOISE CONSIDERATIONS
The STK22C48 is a high-speed memory and so must have a high-frequency bypass capacitor of approximately 0.1F connected between VCAP and VSS, using leads and traces that are as short as possible. As with all high-speed CMOS ICs, normal careful routing of power, ground and signals will help prevent noise problems.
AutoStore OPERATION
The STK22C48 can be powered in one of three modes. During normal AutoStore operation, the STK22C48 will draw current from VCCX to charge a capacitor connected to the VCAP pin. This stored charge will be used by the chip to perform a single STORE operation. After power up, when the voltage on the VCAP pin drops below VSWITCH, the part will automatically disconnect the VCAP pin from VCCX and initiate a STORE operation. Figure 2 shows the proper connection of capacitors for automatic store operation. A charge storage capacitor having a capacity of between 68F and 220F ( 20%) rated at 6V should be provided. In system power mode (Figure 3), both VCCX and VCAP are connected to the + 5V power supply without the 68F capacitor. In this mode the AutoStore function of the STK22C48 will operate on the stored system charge as power goes down. The user must, however, guarantee that VCCX does not drop below 3.6V during the 10ms STORE cycle. If an automatic STORE on power loss is not required, then VCCX can be tied to ground and + 5V applied to VCAP (Figure 4). This is the AutoStore Inhibit mode, in which the AutoStore function is disabled. If the STK22C48 is operated in this configuration, references to VCCX should be changed to VCAP throughout this data sheet. In this mode, STORE operations may be triggered with the HSB pin. It is not permissible to change between these three options "on the fly." In order to prevent unneeded STORE operations, automatic STOREs as well as those initiated by externally driving HSB low will be ignored unless at
SRAM READ
The STK22C48 performs a READ cycle whenever E and G are low and W and HSB are high. The address specified on pins A0-10 determines which of the 2,048 data bytes will be accessed. When the READ is initiated by an address transition, the outputs will be valid after a delay of tAVQV (READ cycle #1). If the READ is initiated by E or G, the outputs will be valid at tELQV or at tGLQV, whichever is later (READ cycle #2). The data outputs will repeatedly respond to address changes within the tAVQV access time without the need for transitions on any control input pins, and will remain valid until another address change or until E or G is brought high, or W or HSB is brought low.
SRAM WRITE
A WRITE cycle is performed whenever E and W are low and HSB is high. The address inputs must be stable prior to entering the WRITE cycle and must remain stable until either E or W goes high at the end of the cycle. The data on the common I/O pins DQ0-7 will be written into the memory if it is valid tDVWH before the end of a W controlled WRITE or tDVEH before the end of an E controlled WRITE. It is recommended that G be kept high during the entire WRITE cycle to avoid data bus contention on common I/O lines. If G is left low, internal circuitry will turn off the output buffers tWLQZ after W goes low.
Document Control #ML0004 Rev 0.3 February 2007
8
STK22C48
least one WRITE operation has taken place since the most recent STORE or RECALL cycle. If the power supply drops faster than 20 s/volt before VCCX reaches VSWITCH, then a 2.2 ohm resistor should be inserted between VCCX and the system supply to avoid momentary excess of current between Vccx and Vcap. operate in this mode the HSB pin should be connected together to the HSB pins from the other STK22C48s. An external pull-up resistor to + 5V is required since HSB acts as an open drain pull down. The VCAP pins from the other STK22C48 parts can be tied together and share a single capacitor. The capacitor size must be scaled by the number of devices connected to it. When any one of the STK22C48s detects a power loss and asserts HSB, the common HSB pin will cause all parts to request a STORE cycle (a STORE will take place in those STK22C48s that have been written since the last nonvolatile cycle). During any STORE operation, regardless of how it was initiated, the STK22C48 will continue to drive the HSB pin low, releasing it only when the STORE is complete. Upon completion of the STORE operation the STK22C48 will remain disabled until the HSB pin returns high. If HSB is not used, it should be left unconnected.
HSB OPERATION
The STK22C48 provides the HSB pin for controlling and acknowledging the STORE operations. The HSB pin is used to request a hardware STORE cycle. When the HSB pin is driven low, the STK22C48 will conditionally initiate a STORE operation after tDELAY; an actual STORE cycle will only begin if a WRITE to the SRAM took place since the last STORE or RECALL cycle. The HSB pin acts as an open drain driver that is internally driven low to indicate a busy condition while the STORE (initiated by any means) is in progress. Pull up this pin with an external 10K ohm resistor to VCAP if HSB is used as a driver.
SRAM READ and WRITE operations that are in
PREVENTING STORES
The STORE function can be disabled on the fly by holding HSB high with a driver capable of sourcing 30mA at a VOH of at least 2.2V, as it will have to overpower the internal pull-down device that drives HSB low for 20s at the onset of a STORE. When the STK22C48 is connected for AutoStore operation (system VCC connected to VCCX and a 68F capacitor on VCAP) and VCC crosses VSWITCH on the way down, the STK22C48 will attempt to pull HSB low; if HSB doesn't actually get below VIL, the part will stop trying to pull HSB low and abort the STORE attempt.
progress when HSB is driven low by any means are given time to complete before the STORE operation is initiated. After HSB goes low, the STK22C48 will continue SRAM operations for tDELAY. During tDELAY, multiple SRAM READ operations may take place. If a WRITE is in progress when HSB is pulled low it will be allowed a time, tDELAY, to complete. However, any SRAM WRITE cycles requested after HSB goes low will be inhibited until HSB returns high. The HSB pin can be used to synchronize multiple STK22C48s while using a single larger capacitor. To
10k
0.1F Bypass
10k 10k
1 32 31 30
10k
10k
1 32 31 30 16 17
1
32 31 30
68F 6v, 20%
+
0.1F Bypass
0.1F Bypass
16 16 17
17
Figure 2: AutoStore Mode
Figure 3: System Power Mode
Figure 4: AutoStore Inhibit Mode
*If HSB is not used, it should be left unconnected.
Document Control #ML0004 Rev 0.3 February 2007
9
10k
STK22C48
HARDWARE PROTECT
The STK22C48 offers hardware protection against inadvertent STORE operation and SRAM WRITEs during low-voltage conditions. When VCAP < VSWITCH, all externally initiated STORE operations and SRAM WRITEs are inhibited. AutoStore can be completely disabled by tying VCCX to ground and applying + 5V to VCAP. This is the AutoStore Inhibit mode; in this mode STOREs are only initiated by explicit request using the HSB pin. shows the relationship between ICC and READ cycle time. Worst-case current consumption is shown for both CMOS and TTL input levels (commercial temperature range, VCC = 5.5V, 100% duty cycle on chip enable). Figure 6 shows the same relationship for WRITE cycles. If the chip enable duty cycle is less than 100%, only standby current is drawn when the chip is disabled. The overall average current drawn by the STK22C48 depends on the following items: 1) CMOS vs. TTL input levels; 2) the duty cycle of chip enable; 3) the overall cycle rate for accesses; 4) the ratio of READs to WRITEs; 5) the operating temperature; 6) the Vcc level; and 7) I/O loading.
LOW AVERAGE ACTIVE POWER
The STK22C48 draws significantly less current when it is cycled at times longer than 50ns. Figure 5
100
100
Average Active Current (mA)
Average Active Current (mA)
80
80
60
60 TTL CMOS 20
40 TTL 20 CMOS 0 50 100 150 Cycle Time (ns) 200
40
0 50 100 150 Cycle Time (ns) 200
Figure 5: Icc (max) Reads
Figure 6: Icc (max) Writes
Document Control #ML0004 Rev 0.3 February 2007
10
STK22C48
ORDERING INFORMATION
STK22C48 - N F 45 I TR
Packing Option
Blank = Tube TR = Tape and Reel
Temperature Range
Blank = Commercial (0 to 70C) I = Industrial (-40 to 85C)
Access Time
25 = 25ns 45 = 45ns
Lead Finish
F = 100% Sn (Matte Tin)
Package
N = Plastic 28-pin 300 mil SOIC S = Plastic 28-pin 330 mil SIOC
Document Control #ML0004 Rev 0.3 February 2007
11
STK22C48
Ordering Information
Item Number STK22C48-NF25 STK22C48-NF45 STK22C48-SF25 STK22C48-SF45 STK22C48-NF25TR STK22C48-NF45TR STK22C48-SF25TR STK22C48-SF45TR STK22C48-NF25I STK22C48-NF45I STK22C48-SF25I STK22C48-SF45I STK22C48-NF25ITR STK22C48-NF45ITR STK22C48-SF25ITR STK22C48-SF45ITR Item Name 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM Temperature Commercial Commercial Commercial Commercial Commercial Commercial Commercial Commercial Industrial Industrial Industrial Industrial Industrial Industrial Industrial Industrial
SOP28-300 SOP28-300 SOP28-330 SOP28-330
5V 2Kx 8 AutoStore nvSRAM SOP28-300 5V 2Kx 8 AutoStore nvSRAM SOP28-300 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM 5V 2Kx 8 AutoStore nvSRAM SOP28-330 SOP28-330 SOP28-300 SOP28-300 SOP28-330 SOP28-330 SOP28-300 SOP28-300 SOP28-330 SOP28-330
Document Control #ML0004 Rev 0.3 February 2007
12
STK22C48 Package Diagrams
28-Lead, 300 mil SOIC Gull Wing
0.292 7.42 0.300 7.59
(
)
0.400 10.16 0.410 10.41
(
)
Pin 1 Index
.050 (1.27) BSC
0.701 17.81 0.711 18.06
(
)
0.097 2.46 0.104 2.64
(
)
0.090 2.29 0.094 2.39
(
)
0.014 0.35 0.019 0.48
(
)
0.005 0.12 0.012 0.29
(
)
0.009 0.23 0.013 0.32
(
)
0.024 0.61
0 8
DIM = INCHES DIM = mm
MIN MAX
(
)
MIN ( MAX)
Document Control #ML0004 Rev 0.3 February 2007
13
STK22C48
28-Lead, 330 mil SOIC Gull Wing
0.713 0.733
( 18.11 ) 18.62
0.112 (2.845)
0.004 (0.102)
0.020 0.014
( 0.508 ) 0.356
0.050 (1.270)
0.103 0.093
( 2.616 ) 2.362
0.336 0.326
( 8.534 ) 8.280
Pin 1
0.477 0.453
( 12.116 ) 11.506
0.014 0.008
( 0.356 ) 0.203
0.044 0.028
10 0
( 1.117 ) 0.711
DIM = INCHES DIM = mm
MIN MAX
MIN ( MAX )
Document Control #ML0004 Rev 0.3 February 2007
14
STK22C48
Document Revision History
Revision 0.0 0.1 0.2 0.3
Date December 2002 September 2003 March 2006 February 2007
Summary Removed 20 nsec device. Added lead-free lead finish Obsolete: 35ns speed grade, Plastic DIP packages and Leaded Lead Finish Add Fast Power-Down Slew Rate Information Add Tape Reel Ordering Options Add Product Ordering Code Listing Add Package Drawings Reformat Entire Document
SIMTEK STK22C48 Datasheet, February 2007 Copyright 2007, Simtek Corporation. All rights reserved. This datasheet may only be printed for the expressed use of Simtek Customers. No part of the datasheet may be reproduced in any other form or means without the express written permission from Simtek Corporation. The information contained in this publication is believed to be accurate, but changes may be made without notice. Simtek does not assume responsibility for, or grant or imply any warranty, including MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE regarding this information, the product or its use. Nothing herein constitutes a license, grant or transfer of any rights to any Simtek patent, copyright, trademark, or other proprietary right.
Document Control #ML0004 Rev 0.3 February 2007
15

▲Up To Search▲

Price & Availability of STK22C48

	To Download STK22C48 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .